PYLE Audio Stereo System PLCD82MP User Guide

PLCD82MP  
INSTRUCTION MANUAL  
USA  
EUROPE  
IMPORTANT:  
This radio is set to USA frequency by factory, if European  
frequency is required please flip the frequency step switch on  
the side of the unit.  
After the switchover of the frequency switch, the frequency convert  
function will not be valid until the RESET button has been pressed.  
(The RESET button is in the rear facet of the front panel)  
AUTO-LOADING DISC CD/MP3 ESP PLAYER  
AM/FM-STEREO DIGITAL PLL TUNING RADIO WITH  
ANTI-THEFT FLIP DOWN DETACHABLE FRONT PANEL  
AND MULTI-COLOUR LCD  
INFRA-RED REMOTE CONTROL FUNCTION  
 
SPEAKER CONNECTION  
DISC PLAY:  
ANTENNA PLUG  
YELLOW  
Cleaning discs  
Before playing, clean the disc with a clean, lint-free cloth.  
Wipe the disc in the direction of the arrow.  
7 A  
AUX LINE IN  
RED R  
MEMORY B+  
FUSE  
WHITE L  
BLACK(GND)  
RED (B+)  
0.5 A  
FUSE  
RCA LINE OUT  
GRAY  
RED R  
WHITE L  
FRONT  
BLUE AUTO ANT  
+
+
WHITE  
FRONT  
RIGHT  
SP  
WHITE/BLACK  
GREEN  
GRAY/BLACK  
VIOLET  
NOTE:  
. Do not use so solvents such as benzine, thinners. Commercially available  
cleaners or anti static spray damage the unit.  
LEFT  
SP  
+
+
REAR  
REAR  
GREEN/BLACK  
VIOLET/BLACK  
Do not insert a disc with the label surface down. Doing so may damage the  
unit.  
NOTE:  
1. In spite of having any kinds of speaker system, must use 4 ohms  
impedance of speaker to reduce the distortion during high volume level.  
2. Do not allow the auto antenna wire and ground touch each other.  
Label  
surface up  
SPECIFICATION  
GENERAL  
NOTE:  
Power requirement...............................................................................................DC 13.8V.  
Current consumption..............................................................................................7A MAX.  
POWER OUTPUT...................................................................................................4 X 40W.  
FM SECTION  
Frequency range.......................................................................87.5MHz -108MHz(EUROPE)  
Frequency range..........................................................................87.5MHz -107.9MHz(USA)  
Usable sensitivity..........................................................................................................3uV.  
I.F Frequency.......................................................................................................10.7MHz.  
AM SECTION  
. Do not try to insert another disc when one has been already inserted.  
Doing so may damage the unit.  
.Handle the disc by its edge. And to keep the disc clean, do not touch  
the surface.  
Frequency range......................................................................522KHz - 1620KHz(EUROPE)  
Frequency range............................................................................530KHz - 1710KHz(USA)  
I.F Frequency..........................................................................................................450KHz  
Usable Sensitivity........................................................................................................40dB  
LINE - OUT [OPTION]  
Output......................................................................................................CD MAX 800mv  
CD PLAYER  
.Do not stick paper or tape on the disc.  
System........................................................................................compact disc audio system.  
Usable disc................................................................................CD/CD-R/CD-RW/MP3 disc  
No of quantization bits 1bit.  
Signal format.............................................................................sampling frequency 44.1KHz.  
Frequency characteristics............................................................................20-100Hz < 5dB  
10-20KHz < 5dB.  
.Do not expose the disc to direct sunlight or heat sources such as hot air  
ducts. Or leave it in a car parked in direct sunlight where there can be a  
considerable rise in temperature.  
Signal to noise CD............................................................................................50dB [1KHz]  
Number of channels..............................................................................................2 STEREO.  
Chassis dimensions.......................................................................178[W] X 50[H] X 165[D].  
9
2
 
REMOTE CONTROL BASICS BATTERY REPLACEMENT:  
1.Remove the battery holder as the direction indicated by the arrow.  
2.Replace the battery Set a new battery property with (+)side up.  
3.Insert the battery holder. Push in the holder to the original position.  
INSTALLATION  
INSTALLATION WAY  
IT IS AN ANTI-THEFTINSTALLATION WAY. THECHASSIS WEAR A METAL  
NOTE ON BATTERIES:  
Old batteries must immediately be removed and disposed.  
SLIDING HOUSING. PLEASE HAVE THE WIRING CONNECTIONOF THE  
POWER SUPPLY, SPEAKERS AND ANTENNAAS FOR THE REQUIREMENT  
OF THE MANUAL, THENINSTALL THE METAL SLIDING HOUSING INTOTHE  
CAR ACCORDING TO THEDIAGRAM.  
TO BOOST UP THECAPABILITY OF  
ANTI-JAMMING, PLEASE FIX THE  
METAL STRAP ONTHE METAL  
CONNECTED TO THE BOTTOM  
BRACKET OF THE CAR.  
BATTERY INFORMATION:  
Designated Battery: UM-4"AAA"/R05  
Battery Life: 6 months with normal use (in normal room temperatur)  
SELECT THE PROPER FIXER  
FOR FIXING THE SLIDING  
METAL HOUSING.  
METAL STRAP  
CAUTION:  
Improper use of batteries may cause overheating, explosion or ignition. Resulting in  
jury or fire .Battery leakage may cause damage to the unit.  
Do not disassemble or short the batteries. Do not throw the batteries into the fire.  
To avoid the risk of accident, keep the batteries out of reach of children.  
UNIT CHASSIS  
PLASTIC TRIM OUT  
DASH BOARD  
FRONT PANEL  
SLIDING METAL HOUSING  
TO DRAW THE CHASSISOUT OF THE  
SLIDING METAL HOUSING,INSERT  
THE LEFT AND RIGHTKEY PLATES  
INTO THE RIGHT POSITIONOF THE  
2 SIDES OF CHASSIS.  
TO INSTALL THEFRONT PANEL  
BACK INTO THE UNITCHASSIS,  
FIRSTLY INSTALLTHE RIGHT  
SIDE IF IT BACKINTO THE RIGHT  
POSITION, THEN PUSH THELEFT  
SIDE BACK TO THEUNIT CHASSIS  
TILL OK.  
NOTE  
REMOVE AWAY 2SCREWS FOR PROTECT  
THE DECK BEFORE OPERATING IT.  
REMOVE THE SLIDING  
METAL HOUSING AWAY  
1. LOCAL/DISTANCE BUTTON  
If you findthe receiving signal is weak andthere is the  
word LOC displayed on LCD whenyou tune fordistance  
station, firstly press the button todisappear the word  
LOC on LCD, then tune againfor the distancestation.  
If you findthe interference to the receiving signal is very  
strong and there is not theword LOC displayed on LCD  
when you tunefor local station, firstly press the button to  
display the word LOC on LCD, then tune again for the local  
station.  
PRESS RESET BUTTON TORESUME  
THE DISTORTED PROGRAM WHEN  
THE LCD DISPLAYIMPROPERLY AND  
SOME BUTTONS ARE INVALID.  
RESET BUTTON  
AFTER FLIPPING DOWN THE  
FRONT PANEL, DRAWTHE  
FRONT PANEL OUTOF THE  
CLIP.  
2. LOUDNESS BUTTON  
Press it to enhance the BASSsound effect immediately  
when it isin BASE mode.  
OPEN BUTTON  
TO INSERT DISC INTOCOMPARTMENT OR EJECT DISCOUT  
OF THE COMPARTMENT ORTAKE THE FRONTPANEL AWAY  
THE UNIT CHASSIS, PRESSTHE OPEN BUTTON TOFLIP  
DOWN THE FRONT PANEL.  
3
8
 
LOCATION AND FUNCTION OF CONTROLS  
12. PRESET STATION [ 1-6 ] AND TOP/CDP, INT, RPT, RDM BUTTONS.  
(A].To memorize the current frequency, press any one of the six  
preset buttons hold for more than 2 seconds.  
(B].To recall the preset memory, press one of the preset buttons  
[1-6].  
(C).In CDP mode, press TOP/CDP button to pause CDP playback,  
press it again to resume CDP playback. Press it hold for more  
than about 0.5 seconds to play the first track of the disc.  
(D).In CDP mode, press INT button to play the first 10 seconds part  
of each track, press it again to stop INT mode and retain playing  
the track currently selected.  
(E).In CDP mode, press RPT button to play the current track repeatedly.  
Press it again to cancel this mode.  
(F).In CDP mode, press RDM button to play the track in random order.  
Press it again to cancel this mode.  
(G).In MP3 mode, M5 and M6 is assigned as 10 TRACK up/down when  
normal play.  
1. V-SEL/MENU/ENTER(SEL) AND V-UP/DN, MENU-UP/DN(+/-) BUTTONS  
(1).Press SEL button shortly and repeatedly to select sound mode VOLUME,  
BASS(without preset DSP), TREBLE(without preset DSP), BALANCE and  
FADER, then press + or - button to adjust level of the selected sound mode.  
(2).Press SEL button hold for more than 1 second to turn on MENU mode,  
and the LCD will display DSP OFF/POP M/ROCK M/CLASS M/FLAT M,  
then press SEL button shortly and repeatedly to select ESP12/ESP45,  
BEEP ON/BEEP OFF, SEEK1/SEEK2, VOL LAST/VOL ADJ(When it is in  
VOL ADJUST mode, the next mode will be A-VOL after VOL ADJUST mode,  
then you can adjust the volume level) in the sequence and circulation.  
After select the desired MENU mode, press + or - button to select the  
mode of the selected MENU.  
(3).TRACK SEARCH MODE during MP3 mode:  
A.Press A.P button once to select TRACK SEARCH mode, the LCD will  
display TRK SCH.  
B.Press SEL button to enter TRACK mode, the LCD will display 001 and flash  
unit s digit 1. Then press + or - button to shift the unit s digit from 0 to  
9 as a loop rotation. (Finally press SEL button hold for more than 0.5  
seconds to play the selected track)  
13. MODE BUTTON  
Press it to select RADIO or CDP mode.  
14. INFRA-RED REMOTE CONTROLLING SENSOR  
CAUTION: Do not install the detachable panel before connecting the wire.  
1. The unit is designed for negative terminal of the battery which is connected to the  
vehicle metal. Please confirm it before installation.  
2. If the car interior is extremely hot, as after being parked in the sun, do not use  
the player until the car has been driven for a while to cool off the interior.  
3. Press the OPEN button to flip down the front panel (see fig.1), then take away the  
front panel (see fig.2) and put it in the protective case (see fig.3) safe keeping.  
4. Install the front panel back into its bracket and then push it back to the position for  
playing (see fig.4).  
C.Press SEL button to flash tens digit, then press + or - button to shift the  
tens digit from 0 to 9 as a loop rotation.(Finally press SEL button hold for  
more than 0.5 seconds to play the selected track)  
D.Press SEL button to flash hundreds digit, then press + or - button to shift  
the hundreds digit from 0 to 9 as a loop rotation.  
E.Press SEL button to play the selected track.(If the selected track number  
is bigger than the biggest track number in the MP3 disc, it will play the  
last track in the MP3 disc.)  
7
4
 
(4). FILE SEARCH during MP3 mode:  
A. Press A.P button shortly twice to select FILE SEARCH mode, the  
LCD will display FILE SCH.  
B. Press SEL button shortly once to select and display the first folder.  
Then press + or - button to select the folder with step by step forward  
or backward.  
(2)In CD mode, press ^ button to play next track. Press v button  
once to play the current track from the beginning of the current  
track, press v button twice continuously to play the last track.  
Press ^ or v button hold to skip forward or backward.  
5. AUTO-STORAGE/PRESET MEMORY SCAN BUTTON  
* Press SEL button hold for more than 0.5 second to play the first  
track of the selected folder.  
(1)In radio mode, press it to perform all stations memory for 5 seconds  
each time, while memory digital and frequency will flash on LCD. If  
the button is pressed for more than 2 seconds, it will seek station  
on current band, then write to the preset memories. When the  
auto-storage operation is completed, it will automatically perform  
for 5 seconds each time. During the memory station performing,  
press 1-6 digital buttons to select and stop scanning function.  
(2)In MP3 mode, press A.P button repeatedly to select TRACK SEARCH,  
FILE SEARCH or CHARACTER SEARCH mode.  
C. Press SEL button shortly once to select and display the first track  
of the selected folder. Then press + or - button to select the track  
in the folder with step by step forward or backward.  
D. Press SEL button shortly once to play the selected track.  
(5). CHARACTER SEARCH MODE during Mp3 mode:  
A. Press A.P button shortly three times to select CHARACTER SEARCH  
mode, the LCD will display CHAR SCH.  
B. Press SEL button shortly once to display A in the first digit from left  
to right. Then press + or - button repeatedly to select one of A-Z  
and 0-9 and * to replace A. At this time press SEL button hold for  
more than 0.5 seconds to play the track which first character is  
the selected one.  
6. BAND BUTTON  
Press it repeatedly to select your desired radio band during RADIO  
mode.  
C. Press SEL button shortly once to display A in the second digit from  
left to right. Then press + or - button repeatedly to select one of A-Z  
and 0-9 and * to replace A.  
D. Press SEL button shortly once to display A in the third digit from  
left to right. Then press + or - button repeatedly to select one of A-Z  
and 0-9 and * to replace A.  
7. CLOCK BUTTON  
Press CLK button to display time on LCD, then press CLK button  
hold until time flashes on LCD, thirdly press + or - button to adjust  
HOUR or MINUTE.  
8. SCAN BUTTON  
E. Operate as same as above to select the character in the fourth, fifth,  
... Xth digit from left to right.  
F. Press SEL button hold for more than 0.5 second to play the track  
that the name selected.  
Press it to scan up by one channel step with station detection. If a  
valid signal has detected, the current frequency is blinked within 5  
seconds, then press it again to stop scan and remain the current  
frequency; otherwise, the unit continue to scan up by one channel  
step with station detection 5 seconds later.  
NOTE: During CHARACTER SEARCH mode, press A.P button to  
delete the last character.  
9. POWER BUTTON  
2. OPEN BUTTON  
Press any button except the EJECT and OPEN button to turn on the  
unit, press PWR button hold for more than 0.5 seconds to turn off  
the unit.(After switching on the ACC POWER first time for 3 seconds,  
can only turn on the unit)  
Press it to flip down the front panel and you can insert the disc  
into the CD compartment or press the EJ button to eject the disc  
from the disc compartment or take away the front panel.  
3. LCD (LIQUID CRYSTAL DISPLAY)  
10.STEREO/MONO BUTTON  
Press it repeatedly to select STEREO or MONO sound mode.  
4. UP AND DN BUTTONS  
(1)In RADIO mode, press ^ or v button shortly and repeatedly to  
manually tune up or down for the desired radio station with step by  
step. Press ^ or v button hold for more than 0.5 seconds to  
auto-matically tune up or down for the radio station of strong signal.  
11.MUTE BUTTON  
Press the button to eliminate or resume the sound immediately.  
To resume the sound immediately, can also press MODE, BAND, +,  
-, (LOUD) and SEL button.  
5
6
 

Rackmount Solutions Power Supply E1000RM1U User Guide
Radio Shack Stereo Receiver 15 124 User Guide
Roland Musical Instrument AT20s User Guide
Rotel Stereo Amplifier RA 820B User Guide
Runco Projector CL 710 User Guide
Samsung All in One Printer All in One Printer User Guide
Samsung Blu ray Player BD P1200 User Guide
Samsung Home Theater System HT Z510 User Guide
Samsung Printer ML 1710 User Guide
Sanyo Vacuum Cleaner SC 5006 User Guide