OPERATOR’S MANUAL
24 VOLT LITHIUM-ION
RECIPROCATING SAW
VARIABLE SPEED
R854
®
2
4
v
X
L
i
?
NEW BATTERY PACKS MUST BE
CHARGED BEFORE FIRST USE
Your reciprocating saw has been engineered and manufactured to our high standards for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
GENERAL SAFETY RULES
Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
Avoid accidental starting. Ensure the switch is in the
off-position before plugging in. Carrying power tools
with your finger on the switch or plugging in power tools
that have the switch on invites accidents.
WARNING!
Read all instructions. Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious injury. The term “power
tool” in all of the warnings listed below refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught
in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can
reduce dust-related hazards.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Use battery only with charger listed.
MODEL
R854
BATTERY PACK
130377001
CHARGER
140315001
(R85009)
(R85008)
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
3
GENERAL SAFETY RULES
Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the manner
intended for the particular type of power tool, taking
into account the working conditions and the work
to be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from
the battery, avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
BATTERY TOOL USE AND CARE
Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into power tools
that have the switch on invites accidents.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
WARNING!
To reduce the risk of injury, user must read
instruction manual.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
When servicing a power tool, use only identical
replacement parts. Follow instructions in the
Maintenancesectionofthismanual.Useofunauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make a
SPECIFIC SAFETY RULES
Do not crush, drop or damage battery pack. Do not
use a battery pack or charger that has been dropped
or received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged
battery immediately.
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light.
To reduce the risk of serious personal injury, never use
any cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals. If
exposed, flush with water immediately.
Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
For best results, your battery tool should be charged
in a location where the temperature is more than
50°F but less than 100°F. Do not store outside or in
vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and water,
then neutralize with lemon juice or vinegar. If liquid
gets into your eyes, flush them with clean water for
at least 10 minutes, then seek immediate medical
attention. Following this rule will reduce the risk of serious
personal injury.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will also make exposed metal parts of the tool
“live” and shock the operator.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Always wear safety glasses with side shields. Everyday
glasses have only impact resistant lenses. They are NOT
safety glasses. Following this rule will reduce the risk of
eye injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the risk
of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and possibly
injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
Ifthepowersupplycordisdamaged,itmustbereplaced
only by the manufacturer or by an authorized service
center to avoid risk.
4
SAFETY RULES FOR CHARGER
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
Before using battery charger, read all instructions and
cautionary markings in this manual, on battery charger,
battery, and product using battery to prevent misuse of
the products and possible injury or damage.
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet)
Cord Size (AWG)
25'
16
50'
16
100'
16
CAUTION:
To reduce the risk of electric shock or damage to
the charger and battery, charge only lithium-ion
rechargeable batteries as specifically designated
on your charger. Other types of batteries may
burst, causing personal injury or damage.
NOTE: AWG = American Wire Gauge
Do not operate charger with a damaged cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way. Take
it to an authorized serviceman for electrical check to
determine if the charger is in good working order.
Do not use charger outdoors or expose to wet or damp
conditions. Water entering charger will increase the risk
of electric shock.
Use of an attachment not recommended or sold by the
battery charger manufacturer may result in a risk of
fire, electric shock, or injury to persons. Following this
rule will reduce the risk of electric shock, fire, or serious
personal injury.
Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
Unplug charger from outlet before attempting
any maintenance or cleaning to reduce the risk of
electric shock.
Do not abuse cord or charger. Never use the cord to
carry the charger. Do not pull the charger cord rather than
the plug when disconnecting from receptacle. Damage
to the cord or charger could occur and create an electric
shock hazard. Replace damaged cords immediately.
Disconnect charger from the power supply when
not in use. This will reduce the risk of electric shock or
damage to the charger if metal items should fall into the
opening. It also will help prevent damage to the charger
during a power surge.
Make sure cord is located so that it will not be stepped
on, tripped over, come in contact with sharp edges
or moving parts or otherwise subjected to damage or
stress. This will reduce the risk of accidental falls, which
Risk of electric shock. Do not touch uninsulated portion
of output connector or uninsulated battery terminal.
could cause injury, and damage to the cord, which could Save these instructions. Refer to them frequently and
result in electric shock.
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions also
to prevent misuse of the product and possible injury.
Keep cord and charger from heat to prevent damage
to housing or internal parts.
Do not let gasoline, oils, petroleum-based products,
etc. come in contact with plastic parts. They con-
tain chemicals that can damage, weaken, or destroy
plastic.
IMPORTANT SAFETY INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions for battery charger 140315001.
2. Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and product
using battery.
3. CAUTION: To reduce the risk of injury, charge only lithium-ion rechargeable batteries. Other types of batteries may
burst, causing personal injury or damage.
5
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation
of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Frequency (cycles per second)
Power
Watt
min
Minutes
Time
Alternating Current
Direct Current
Type of current
Type or a characteristic of current
Rotational speed, at no load
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
n
o
No Load Speed
Class II Construction
Per Minute
.../min
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
No Hands Symbol
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
To reduce the risk of injury or damage, avoid contact with any hot
surface.
Hot Surface
6
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
WARNING:
CAUTION
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual.
If you do not understand the warnings and
instructions in the operator’s manual, do not use
this product. Call RIDGID customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses
with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked
to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
FEATURES
PRODUCT SPECIFICATIONS
Strokes Per Minute.............................0-2,500 r/min. (RPM)
Charger Input ................................... 120 V, 60 Hz, AC only
Charge Rate ..............................................................1 hour
Length of Stroke...................................................1-3/16 in.
Motor..................................................................24 Volt DC
Switch..........................................................Variable Speed
SWITCH
TRIGGER
LOCK-OFF
BUTTON
BASE (SHOE)
ASSEMBLY
®
SAW
BLADE
2
4
v
X
L
i
?
SHOE
RELEASE LEVER
BATTERY
PACK
BLADE CLAMP
LOCK / RELEASE LEVER
4-1/8 in.
CHARGER
Fig. 1
8
FEATURES
KNOW YOUR RECIPROCATING SAW
See Figure 1.
BASE (SHOE) ASSEMBLY
The shoe assembly can be adjusted forward or backward
to take advantage of the unused portion of the blade, or for
special jobs requiring low blade clearance.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
BLADE CLAMP LOCK / RELEASE LEVER
Your saw has a blade clamp design that does not require
the use of a tool (blade wrench) when installing or removing
the blade.
CHARGER
The charger has a key-hole hanging feature for convenient,
space-saving storage. Screws should be installed so that
the center distance is 4-1/8 in.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with
decreased trigger pressure.
LOCK-OFF BUTTON
Your saw is equipped with a “lock-off” button which reduces
the possibility of accidental starting. The lock-off button is
located on the handle above the switch trigger.
9
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
WARNING:
If any parts are damaged or missing, do not
operate this tool until the parts are replaced.
Failure to heed this warning could result in serious
personal injury.
Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have care-
WARNING:
fully inspected and satisfactorily operated the tool.
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
PACKING LIST
24 Volt Reciprocating Saw
Saw Blades (2)
Battery
WARNING:
Charger
To prevent accidental starting that could cause
serious personal injury, always remove the battery
pack from the tool when assembling parts.
Tool Bag
Operator’s Manual
OPERATION
WARNING:
Do not allow familiarity with your tool to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
WARNING:
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal injury.
WARNING:
APPLICATIONS
Always wear safety goggles or safety glasses with
side shields when operating tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
You may use this tool for the purposes listed below:
Cutting all types of wood products (lumber, plywood,
paneling, composition board, and hard wood)
Cutting masonite and plastic
Cutting drywall
Cutting metals such as sheet steel, pipe, steel rods,
aluminum, brass, and copper
10
OPERATION
CHARGE
LEVEL INDICATOR
CAUTION:
If at any point during the charging process none
of the LEDs are lit, remove the battery pack from
the charger to avoid damaging the product. DO
NOT insert another battery. Return the charger and
battery to your nearest service center for service
or replacement.
24vXLi
?
CAUTION:
Charge in a well ventilated area. Do not block
charger vents. Keep them clear to allow proper
ventilation.
CHARGING THE BATTERY PACK
NOTE: New 24 Volt lithium-ion battery packs will not
work without first being charged. Before first time use,
charge the battery pack to activate it.
It is not necessary to drain the battery pack completely
before recharging. Lithium-ion battery packs have no
“memory” and can be recharged at any time. It is therefore
possible to charge the battery pack before extended usage
even if the battery pack is not completely drained of charge.
Use the charge level indicator to determine the amount of
charge in the battery pack.
Fig. 2
Lithium-ion batteries deliver fade free power for their entire
run time. 24 Volt lithium-ion tools will not gradually lose
power due to decreasing battery charge. Instead, power
from the battery pack will drop from full to zero once the
full charge has been drained from the battery. Once this
happens, your tool’s power drops from full to zero, and
recharging the battery is required.
CHARGING A HOT BATTERY PACK
If the battery pack is above normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery pack cools down to approximately 150°F
(65°C), the charger will automatically begin fast charge mode.
TO CHARGE
NOTE: Refer to CHARGING THE BATTERY PACK for
normal recharging of batteries. If the charger does not charge
the battery pack under normal circumstances, return both
the battery pack and charger to your nearest repair center
for electrical check. For the location of your nearest repair
center, please call 1-866-539-1710.
A fully discharged battery pack with a temperature between
32°F (0°C) and 150°F (65°C) will charge in about an hour.
Charge the 24 Volt lithium-ion battery pack only with the
charger provided.
Connect the charger to a power supply.
NOTE:iIf needed, the charger can operate with most
generators and inverters rated at 300 Watts or higher.
Attach the battery pack to the charger by aligning the
raised ribs on the battery pack with the grooves in the
charger, then slide the battery pack onto the charger. See
Figure 2.
CHARGING A COOL BATTERY PACK
If the battery pack is below normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery warms to a temperature of more than 14°F
(-10°C), the charger will automatically begin charging.
Do not place the charger in an area of extreme heat or
cold. It will work best at normal room temperature.
After charging is complete, the continuous green light
will come on and the charge level indicator lights on the
battery will go off.
COLD WEATHER OPERATION
The lithium-ion battery pack can be used in temperatures
down to -4°F (-20°C). When the battery pack is very cold, it
may “buzz” for the first minute of use to warm itself up. Put
the battery pack on a tool and use the tool in a light duty
application. After about a minute, the pack will have warmed
itself up and begin operating normally.
The charger will keep the battery pack fully charged if left
on the charger.
11
OPERATION
LED FUNCTION OF CHARGER
See Figure 3.
LED
INDICATOR
BATTERY
PACK
RED
LED
GREEN
LED
ACTION
Charging
Fast charging
OFF
Charges in 1 hour
ON
Charger pre-charges battery until
normal voltage is reached, then
begins fast charge mode. May take
longer than 1 hour to fully charge
Charging
OFF
Deeply Discharged
ON
Maintenance
charging
Fast charging is complete
Charger maintains charge mode
Full
OFF
ON
When battery pack reaches cooled
temperature, charger begins fast
charge mode
Flashing
OFF
Evaluate
Hot battery pack
When battery pack reaches warmed
temperature, charger begins fast
charge mode
Evaluate
Defective
Cold battery pack
Defective
Flashing
Flashing
OFF
Flashing
Battery pack or charger is defective
• If defective, try to repeat the conditions a second time by removing and reinstalling the battery
pack. If the LED status repeats a second time, try charging a different battery.
• If a different battery charges normally, dispose of the defective pack (see Maintenance section).
• If a different battery also indicates “Defective,” the charger may be defective.
FULL
CAPACITY
3/4
CAPACITY
RED LED
GREEN LED
CHARGING
INDICATOR
1/2
CAPACITY
24vXL
i
FULL
INDICATOR
?
CHARGE
LEVEL
INDICATOR
BUTTON
EVALUATE
INDICATOR
1/4
CAPACITY
CHARGE
LEVEL INDICATOR
DEFECTIVE
INDICATOR
Fig. 4
CHARGE LEVEL INDICATOR
See Figure 4.
The charge level indicator shows that the battery is charged
at 1/4, 1/2, 3/4, or full capacity. To display the amount of
charge left in the battery, press and hold the charge level
indicator button.
Fig. 3
NOTE: When the battery pack contains less than 10%
charge, the 1/4 charge level indicator will flash.
12
OPERATION
TO INSTALL BATTERY PACK
See Figure 5.
Place the battery pack in the saw aligning raised rib on
battery pack with groove in the saw’s battery port.
Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured to saw
before beginning operation.
®
TO
REMOVE
CAUTION:
TO
When placing battery pack in the tool, be sure
raised rib on battery pack aligns with the grooves
in the bottom of the saw and latches into place
properly. Improper installation of the battery pack
can cause damage to internal components.
INSTALL
2
4
v
X
L
i
RAISED RIB
?
BATTERY PACK
Fig. 5
DEPRESS LATCHES TO
RELEASE BATTERY PACK
TO REMOVE BATTERY PACK
See Figure 5.
Locate the latches on the side of the battery pack and
depress both sides to release the battery pack from the
saw.
SWITCH TRIGGER
TOP VIEW
UNLOCK
Remove the battery pack from the saw.
SWITCH TRIGGER
See Figure 6.
®
To turn the saw ON, slide lock off button to the UNLOCK
position, and press the switch trigger. To turn it OFF, re-
lease the switch trigger.
LOCK
2
4
v
X
L
i
CAUTION:
Lock off button should be in the LOCK position
when saw is not in use or is being transported.
?
Fig. 6
BASE
See Figure 7.
The base of the reciprocating saw pivots in both directions
for ease of use.
CHANGING POSITIONS OF THE SHOE
ASSEMBLY
See Figure 7.
Remove the battery pack.
Unlock the shoe release lever.
Reposition the shoe assembly.
Lock the shoe release lever.
TO LOCK
TO UNLOCK
BASE (SHOE)
ASSEMBLY
SHOE
RELEASE LEVER
Fig. 7
13
OPERATION
BLADE CLAMP
BLADE CLAMP
LOCK / RELEASE LEVER
TO INSTALL SAW BLADE
See Figure 8.
Remove the battery pack from the saw.
Lift the toolless blade clamp lever located on the side of
the saw.
Insert saw blade fully between the toolless blade clamp
BLADE
and saw bar.
Release the toolless blade clamp.
GENERAL CUTTING
See Figure 9.
Rest the front of the saw shoe on the workpiece and align
cutting edge of the blade with the line on the workpiece.
UNLOCK
Fig. 8
LOCK
Startthesawandmoveitforwardontheworksurface. Apply
downwardpressuretokeepthesawsteadyandonlyenough
forward pressure to keep the blade cutting.
CAUTION:
Do not force the saw. Forcing the saw may
overheat the motor and break saw blades.
®
PLUNGE CUTTING
See Figure 10.
WARNING:
To avoid loss of control, broken blades, or dam-
age to the material being cut, always use extreme
caution when making plunge cuts. It is not rec-
ommended to plunge cut materials other than
wood.
Fig. 9
Mark the line of cut clearly on the workpiece.
Tilt the saw forward so that it rests on the front edge
of the shoe and blade will not come in contact with the
workpiece when the saw is turned on.
Make sure the blade is inside the area to be cut.
®
Using high speed, start the saw and slowly lower the
blade into the workpiece until the blade cuts through the
wood.
Continue lowering the blade into the workpiece until the
shoe rests flat on the work surface, then move the saw
forward to complete the opening.
Use only the 7 teeth per inch blade for this type of cut.
Fig. 10
14
OPERATION
METAL CUTTING
See Figure 11.
Many kinds of metals can be cut with the saw. Be careful
not to twist or bend the blades. Do not force. If the blade
chatters or vibrates excessively, use a finer-tooth metal-
cutting blade. If blade heats excessively, use lower speed. If
blade teeth become filled or clogged when cutting soft met-
als, such as aluminum, use a coarser-tooth blade or lower
speed.Werecommenduseofoilwhencuttingmetalstokeep
blades cool, increase cutting action, and prolong blade life.
Clamp the work firmly and saw close to the clamping point
to eliminate any vibration of the work being cut.
®
When cutting conduit, pipe, or angle iron, clamp work in a
vise if possible and saw close to the vise. To cut thin sheet
materials, “sandwich” the material between hardboard or
plywood and clamp the layers to eliminate vibration and
material tearing. By doing this, the material will be cut
smoothly. Lay out your pattern or line of cut on top of the
“sandwich.”
Fig. 11
NOTE: When cutting metal, keep exposed portion of saw
blade clean and free of metal chips by wiping frequently with
an oily cloth. Use extreme caution in disposing of oily cloth
after completion of job to prevent potential fire hazard.
15
MAINTENANCE
GENERAL MAINTENANCE
WARNING:
When servicing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a RIDGID authorized service center.
WARNING:
To avoid serious personal injury, always remove
the battery pack from the tool when cleaning or
performing any maintenance.
BATTERY PACK REMOVAL AND PREPARATION
BATTERIES
The battery pack for this tool is equipped with lithium-ion
rechargeable batteries. Length of service from each charging
will depend on the type of work you are doing.
FOR RECYCLING
To preserve natural resources, please
recycle or dispose of batteries
properly.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
This product contains lithium-ion
batteries. Local, state or federal laws
may prohibit disposal of lithium-ion
Li - Ion
batteries in ordinary trash.
Consult your local waste authority for information regarding
available recycling and/or disposal options.
To obtain the longest possible battery life, we suggest the
following:
Remove the battery pack from the charger once it is fully
WARNING:
charged and ready for use.
Upon removal, cover the battery pack’s terminals
with heavy-duty adhesive tape. Do not attempt to
destroy or disassemble battery pack or remove any
of its components. Lithium-ion batteries must be
recycled or disposed of properly. Also, never touch
both terminals with metal objects and/or body
parts as short circuit may result. Keep away from
children. Failure to comply with these warnings
could result in fire and/or serious injury.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
80°F (27°C ) and away from moisture.
Store battery packs in a 30%-50% charged condition.
Every six months of storage, charge the pack as
normal.
16
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting war-
ranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers de-
fects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID® branded hand held
and stationary power tools. Consumable accessories pro-
vided with the tool such as, but not limited to, blades, bits
and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied war-
ranties, including warranties of MERCHANTABILITY or FIT-
NESS FOR A PARTICULAR PURPOSE, are disclaimed. Any
implied warranties, including warranties of merchantability
or fitness for a particular purpose, that cannot be disclaimed
under state law are limited to three years from the date of
purchase. One World Technologies, Inc. and RIDGID, Inc.
are not responsible for direct, indirect, incidental or conse-
quential damages. Some states do not allow limitations on
how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential dam-
ages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
ging on to the RIDGID® website at www.ridgid.com. When
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will re-
pair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
17
OPERATOR’S MANUAL
24 VOLT LITHIUM-ION
RECIPROCATING SAW
VARIABLE SPEED
R854
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this tool is found on a plate attached to the motor housing.
Please record the serial number in the space provided below. When ordering repair
parts, always give the following information:
R854
Model No.
Serial No.
983000-922
02-22-06 (REV:00)
|