Radio Shack Cell Phone ET 531 User Guide

43-1031.fm Page 1 Tuesday, August 17, 1999 9:24 AM  
Cat. No. 43-1031  
OWNER’S MANUAL  
Please read before using this equipment.  
ET-531  
10-Channel Cordless Telephone  
with 10-Memory Speed Dialing  
 
43-1031.fm Page 3 Tuesday, August 17, 1999 9:24 AM  
This telephone has been tested and  
found to comply with all applicable  
FCC and UL standards.  
READ THIS BEFORE  
INSTALLATION  
We have designed your telephone to  
conform to federal regulations, and  
you can connect it to most telephone  
lines. However, each device that you  
connect to the phone line draws power  
from the phone line. We refer to this  
power draw as the device’s ringer  
equivalence number, or REN. The  
REN is shown on the bottom of your  
phone.  
Note: Your 10-Channel Cordless Tele-  
phone with 10-Memory Speed Dialing  
operates on standard radio frequen-  
cies, as allocated by the FCC. There-  
fore, it is possible for other radio units  
operating on similar frequencies, with-  
in a certain area, to inadvertently inter-  
cept your conversa-tions and/or cause  
interference on your cordless tele-  
phone. This lack of privacy can occur  
with any cordless telephone.  
If you are using more than one phone  
or other device on the line, add up all  
the RENs. If the total is more than five,  
your phone might not ring. In rural ar-  
eas, a total REN of three might impair  
ringer operation. If ringer operation is  
impaired, remove a device from the  
line.  
Warning: To prevent fire or shock haz-  
ard, do not expose this product to rain  
or moisture.  
CAUTION  
RISK OF ELECTRIC SHOCK.  
!
DO NOT OPEN.  
CAUTION: TO REDUCE THE RISK OF  
ELECTRIC SHOCK, DO NOT REMOVE  
COVER OR BACK. NO USER-SERVICE-  
ABLE PARTS INSIDE. REFER SERVIC-  
ING TO QUALIFIED PERSONNEL.  
FCC STATEMENT  
This telephone complies with Part 68  
of FCC Rules. You must, upon re-  
quest, provide the registration number  
and the REN to your phone company.  
These numbers are located on the bot-  
tom of your phone.  
This symbol is intended to alert you  
to the presence of uninsulated dan-  
gerous voltage within the product’s  
enclosure that might be of sufficient  
magnitude to constitute a risk of  
electric shock. Do not open the  
product’s case.  
Note: You must not connect your  
phone to any of the following:  
• Coin-operated systems  
• Party-line systems  
This symbol is intended to inform  
you that important operating and  
maintenance instructions are in-  
cluded in the literature accompany-  
ing this product.  
!
• Most electronic key phone sys-  
tems  
3
 
43-1031.fm Page 4 Tuesday, August 17, 1999 9:24 AM  
CONTENTS  
Preparation ........................................................................................................... 5  
Installing the Battery ........................................................................................ 5  
Installing the Handset’s Antenna .......................................................................5  
Selecting a Location ........................................................................................ 5  
Placing the Base on a Desk Top ............................................................... 6  
Mounting the Base on a Wall Plate ........................................................... 6  
Mounting the Base Directly on the Wall .................................................... 7  
Charging the Battery ........................................................................................ 9  
Setting the Dialing Mode ................................................................................. 9  
Setting the Ringer On/Off .............................................................................. 10  
Operation ............................................................................................................ 11  
Making/Answering a Call ............................................................................... 11  
Using the Handset at the Base ............................................................... 11  
Using the Handset Away from the Base ................................................. 11  
Reducing Interference ................................................................................... 12  
Redial ............................................................................................................ 12  
Using Flash .................................................................................................... 12  
Using Tone Services with a Service Number.................................................. 13  
Using Page .................................................................................................... 13  
Memory Dialing .............................................................................................. 14  
Storing a Number in Memory .................................................................. 14  
Entering a Pause in a Memory Number .................................................. 15  
Dialing a Stored Number ......................................................................... 15  
Chain Dialing Service Numbers .............................................................. 15  
Testing Stored Emergency Numbers ...................................................... 15  
Troubleshooting ................................................................................................. 16  
Care and Maintenance ....................................................................................... 18  
Replacing the Battery .................................................................................... 19  
The FCC Wants You to Know ........................................................................ 19  
Lightning ........................................................................................................ 20  
4
 
43-1031.fm Page 5 Tuesday, August 17, 1999 9:24 AM  
PREPARATION  
INSTALLING THE  
BATTERY  
SELECTING A LOCATION  
You can place your phone on a desk,  
shelf, or table, or mount it on a wall.  
Select a location that is:  
Before you use your phone for the first  
time, you must install and connect the  
battery, then charge it for about 12-15  
hours.  
• Near an AC outlet  
• Near a telephone line jack  
• Out of the way of normal activities  
To install the battery, slide off the bat-  
tery compartment cover on the back of  
the handset. Place the battery in the  
compartment, then connect the battery  
to the pins inside the battery compart-  
ment.  
• Away from fluorescent lights, elec-  
trical machinery, electrical appli-  
ances, and metal walls or filing  
cabinets  
• Away from computers, remote  
control toys, wireless intercoms,  
alarms, and room monitors.  
The base’s location affects the phone’s  
range. If you have a choice of several  
locations, try each to see which pro-  
vides the best performance.  
Then install the handset’s antenna, re-  
place the cover, mount the phone (see  
“Selecting a Location”), and follow the  
instructions under “Charging the Bat-  
tery.”  
Notes:  
• If the phone line jack is not a mod-  
ular jack, you must update the wir-  
ing. You can do this yourself,  
using jacks and adapters avail-  
able at your local Radio Shack  
store, or you can let the phone  
company update the wiring for  
you.  
INSTALLING THE  
HANDSET’S ANTENNA  
Insert the antenna into the hole at the  
top of the handset, then rotate the an-  
tenna clockwise until it is secure.  
• The phone company will charge  
you for the installation of the nec-  
essary jacks.  
5
 
43-1031.fm Page 6 Tuesday, August 17, 1999 9:24 AM  
• The USOC number of the jack to  
be installed is RJ11W for a wall  
jack or RJ11C for a baseboard  
jack.  
5. Place the handset upright over the  
charging contacts on the top of  
the base (see “Charging the Bat-  
tery”).  
Note: The phone will not charge if  
you try to use the charging con-  
tacts on the side of the base while  
it is flat on a desk top.  
Caution: You must use a 120 VAC/12  
VDC adapter that delivers at least 200  
milliamps. Its plug must correctly fit the  
12VDC  
phone’s  
jack. The supplied  
adapter meets these requirements.  
Using an adapter that does not meet  
these requirements could damage the  
phone or the adapter.  
6. Fully extend the base’s antenna  
and place it in a vertical position.  
Mounting the Base on a Wall  
Plate  
Placing the Base on a Desk  
Top  
You need a short modular cord (such  
as Radio Shack Cat. No. 279-390, not  
supplied) and a standard wall plate for  
this mounting method.  
1. Plug one end of the short modular  
TEL. LINE  
cord into the  
back of the base.  
jack on the  
Follow these steps when you place the  
base on a desk, shelf, or table.  
1. Plug one end of the supplied mod-  
TEL. LINE  
ular cord into the  
on the back of the base.  
jack  
2. Route the short cord downward  
through the slot on the base’s bot-  
tom and under the clips as shown.  
2. Plug the modular cord’s other end  
into a modular phone line jack.  
3. Insert the supplied AC adapter’s  
12VDC  
barrel plug into the  
jack on  
the back of the base.  
4. Plug the adapter into a standard  
AC outlet.  
6
 
43-1031.fm Page 7 Tuesday, August 17, 1999 9:24 AM  
3. Route the other end of the short  
cord through the hole in the  
bracket’s center.  
7. Align the bracket’s keyhole slots  
with the wall plate studs and slide  
the base downward to secure it.  
4. Attach the supplied bracket to the  
bottom of the base by inserting  
the tabs on the bracket into the  
slots on the base, then sliding the  
bracket up.  
8. Carefully place the handset in the  
cradle at the top of the base and  
make sure it is secure.  
If you later want to mount  
Note:  
the base on a desktop, press  
PUSH on the bracket and pull it off  
to remove it.  
5. Insert the supplied AC adapter’s  
barrel plug into the 12VDC jack on  
the back of the base. Then plug  
the adapter into a standard AC  
outlet.  
9. Fully extend the base’s antenna  
and place it in a vertical position.  
Mounting the Base Directly  
on the Wall  
You need two wood screws (not sup-  
plied) for this mounting method.  
1. Drill two holes 315/16 inches apart.  
Then thread a screw into each  
6. Plug the modular cord into the  
wall plate’s jack.  
1
hole, letting the heads extend /4  
inch from the wall.  
7
 
43-1031.fm Page 8 Tuesday, August 17, 1999 9:24 AM  
2. Plug one end of the supplied mod-  
ular cord into the TEL. LINE jack  
on the back of the base.  
6. Plug the modular cord into a mod-  
ular phone line jack.  
3. On the bottom of the base, route  
the modular cord downward and  
under the slot’s clips as shown.  
7. Align the keyhole slots with the  
mounting screws and slide the  
base downward to secure it.  
4. Attach the supplied bracket to the  
bottom of the base by inserting  
the tabs on the bracket into the  
slots on the base, then sliding the  
bracket up.  
8. Carefully place the handset in the  
cradle at the top of the base and  
make sure it is secure.  
If you later want to mount  
Note:  
the base on a desktop, press  
PUSH on the bracket and pull it off  
to remove it from the base’s bot-  
tom.  
9. Fully extend the base’s antenna  
and place it in a vertical position.  
5. Insert the supplied AC adapter’s  
barrel plug into the 12VDC jack on  
the back of the base. Then plug  
the adapter into a standard AC  
outlet.  
8
 
43-1031.fm Page 9 Tuesday, August 17, 1999 9:24 AM  
• If the CHARGE indicator does not  
light when you place the handset  
on the cradle, be sure the battery  
is connected to the pins inside the  
battery compartment, and the AC  
adapter is securely connected to  
the base.  
CHARGING THE  
BATTERY  
Before you use your phone for the first  
time or when you install a new battery,  
RINGER ON/OFF  
make sure  
on the  
OFF  
handset is set to  
, then charge the  
battery for about 12-15 hours by plac-  
ing the handset on the cradle so the  
POWER and CHARGE indicators  
light.  
Also, check the charging contacts  
on the handset and base. If the  
contacts are dirty or tarnished,  
gently clean them with a pencil  
eraser.  
The phone charges whenever the  
handset is on the base. You can re-  
charge the battery at any time, but be  
sure to recharge it when BATT LOW  
lights on the handset.  
• About once a month, fully dis-  
charge the battery. Keep the  
handset off the cradle until BATT  
LOW lights. Then return the hand-  
set to the cradle and recharge the  
battery for about 10 hours.  
Notes:  
• Continuing to use the battery after  
BATT LOW lights could shorten  
overall battery life.  
SETTING THE DIALING  
MODE  
• The first time you use your phone  
after installing a new battery, the  
handset might not work or might  
sound an error tone when you  
TONE/PULSE  
Set  
on the base for the  
type of service you have. If you are not  
sure which type you have, do this test.  
TALK  
press  
. This might also occur  
TONE/PULSE  
TONE.  
to  
1. Set  
when you recharge a battery that  
has been completely discharged.  
RINGER  
If this happens, be sure  
ON/OFF  
ON  
. Then return  
is set to  
the handset to the cradle for 5  
seconds. This resets the security  
access code.  
9
 
43-1031.fm Page 10 Tuesday, August 17, 1999 9:24 AM  
2. Lift the handset, press TALK, and  
SETTING THE RINGER  
ON/OFF  
listen for a dial tone.  
3. Press any number other than 0.  
To turn off the ringer, set RINGER ON/  
OFF on the handset to OFF. To turn on  
the ringer, set it to ON.  
If the dial tone stops, you have touch-  
tone service. Leave TONE/PULSE set  
to TONE.  
If the dial tone continues, you have  
pulse (rotary) service. Set TONE/  
PULSE to PULSE.  
With the handset’s ringer off,  
Note:  
you can still make and receive calls us-  
ing the cordless phone. Telephones on  
the same line still ring when there is an  
incoming call, the handset’s IN USE in-  
dicator flashes, and the POWER and  
CHARGE indicators on the base flash  
until you answer the call.  
10  
 
43-1031.fm Page 11 Tuesday, August 17, 1999 9:24 AM  
OPERATION  
Before using your cordless telephone,  
you must install and charge its battery  
(see “Installing the Battery” and  
“Charging the Battery”). For the best  
operation, make sure the base’s an-  
tenna is fully extended.  
To disconnect a call, replace the hand-  
set on the base.  
Using the Handset Away from  
the Base  
To use the handset away from the  
base, press TALK to make or answer a  
call. The IN USE indicator on the hand-  
set lights.  
MAKING/ANSWERING A  
CALL  
You can use your cordless telephone  
in two ways: at the base or away from  
the base.  
To disconnect a call, press TALK so  
the IN USE indicator on the handset  
turns off.  
Notes:  
Using the Handset at the  
Base  
• Press TALK so the IN USE indica-  
tor turns off when you are not  
making or answering a call, to  
conserve battery power and leave  
the phone line available.  
You can use the handset at the base  
like a regular corded telephone. Place  
the handset in the cradle. The base  
rings whether RINGER ON/OFF on the  
handset is set to ON or OFF.  
• You can make or answer a call on  
another phone on the same  
phone line, even if the handset is  
away from the base.  
To answer a call, just lift the handset  
from the base.  
To make a call, lift the handset from  
the base and press TALK so the IN  
USE indicator lights.  
11  
 
43-1031.fm Page 12 Tuesday, August 17, 1999 9:24 AM  
REDUCING  
USING FLASH  
INTERFERENCE  
FLASH  
Use  
on the handset to perform  
the switchhook operation for special  
services, such as call waiting.  
To reduce interference between the  
CHANNEL  
handset and the base, press  
to switch to the next channel (10 in all)  
until you receive the best reception.  
For example, if you have call waiting,  
FLASH  
press  
to take an incoming call  
without disconnecting the current call.  
FLASH  
Press  
call.  
again to return to the first  
REDIAL  
To quickly redial the last number di-  
aled, simply lift the handset from the  
TALK  
cradle or press  
so the IN USE in-  
REDIAL.  
dicator lights. Then press  
Notes:  
• If you do not have a special phone  
RE-  
to dial numbers that include a  
entry (see “Using Tone Services  
Note: We recommend you not use  
DIAL  
TONE  
FLASH  
service, pressing  
disconnect the current call.  
might  
with a Service Number”).  
• The redial memory does not store  
FLASH  
a
entry or any digits  
FLASH  
entered after you press  
.
12  
 
43-1031.fm Page 13 Tuesday, August 17, 1999 9:24 AM  
USING TONE SERVICES  
WITH A SERVICE  
NUMBER  
USING PAGE  
PAGE  
lets you locate the handset if you  
misplaced it, or alert the person hold-  
ing the handset. The handset sounds  
four beeps when someone presses  
Some special services, such as bank  
by phone, require tone signals. If you  
have pulse service, you can still use  
these special tone services by follow-  
ing these steps.  
PAGE  
on the base. The IN USE indica-  
tor and the selected channel appear on  
the base’s display.  
TONE/PULSE  
1. Set  
on the base to  
PULSE  
.
Note: The handset will not beep during  
a call, or if the ringer is off.  
2. Dial the service’s main number.  
3. When the service answers, press  
(S). Then dial the additional num-  
bers. The phone sends these  
numbers as tone signals.  
4. When you complete the call, place  
the handset on the cradle or press  
TALK  
to disconnect the call. The  
phone automatically resets to the  
pulse mode.  
RE-  
to dial numbers that include a  
entry.  
Note: We recommend you not use  
DIAL  
TONE  
13  
 
43-1031.fm Page 14 Tuesday, August 17, 1999 9:24 AM  
MEMORY  
4. Press  
again.  
MEMORY DIALING  
5. Press the memory location num-  
ber (0 to 9) where you want to  
store the number. A long beep  
sounds. The phone number is  
now stored in memory.  
You can store up to 10 phone numbers  
for single-button dialing. Each stored  
number can be up to 16 digits long.  
Notes:  
6. Remove the plastic covering from  
the handset’s index card with a  
small pointed object, such as the  
end of a straightened paper clip.  
Write the person’s or company’s  
name and memory location num-  
ber on the card in pencil (in case  
you want to change it later).  
TONE/PULSE  
PULSE  
is set to  
• If  
and you want to use tone dialing  
for a memory number, you must  
store the tone entry (S) along with  
the number.  
To keep your accounts secure, we  
recommend you not store your  
personal access code for services  
such as bank-by-phone in a mem-  
ory location.  
7. Repeat Steps 2-6 to store and  
record other telephone numbers.  
Notes:  
Storing a Number in Memory  
• If you receive a call while you are  
storing a number in memory,  
TALK  
1. If necessary, press  
on the  
TALK  
press  
to answer the call.  
handset so the IN USE indicator  
turns off.  
After the call, begin again at Step  
1 to store the number.  
MEMORY  
2. Press  
.
To change a phone number stored  
in memory, simply store a new  
phone number in that position.  
To clear a memory position so no  
MEM-  
number is stored in it, press  
ORY  
twice, then press the memory  
location number. A long beep  
sounds. The phone number is  
now cleared from memory.  
Note: While you are storing a  
number in memory, if you do not  
press any button within 10 sec-  
onds, you must repeat Step 2 and  
try again.  
Note: A fast beeping pattern indicates  
that your clearing was unsuccessful.  
Try the process again.  
3. Dial the number you want to store.  
14  
 
43-1031.fm Page 15 Tuesday, August 17, 1999 9:24 AM  
Entering a Pause in a Memory  
Number  
Chain Dialing Service  
Numbers  
In some telephone systems, you must  
dial an access code (9, for example)  
and wait for a second dial tone before  
you can dial an outside number. If your  
phone is connected to one of these  
systems, you might want to enter a  
pause at the appropriate point when  
you store a phone number in memory.  
When calling special services (such as  
alternate long distance or bank by  
phone), dial the service’s main number  
first. Then, at the appropriate place in  
the call, press MEMORY and the num-  
ber for the location where the addition-  
al information is stored.  
Testing Stored Emergency  
Numbers  
When storing a number, press PAUSE  
to enter a 3-second pause. For a long-  
er pause, press PAUSE again (each  
press enters a 3-second pause).  
If you store an emergency service’s  
number (police department, fire de-  
partment, ambulance) and you choose  
to test the stored number, make the  
test call during the late evening or early  
morning hours to avoid peak demand  
periods. Also, remain on the line to ex-  
plain the reason for your call.  
Dialing a Stored Number  
Follow these steps to dial a number  
stored in memory.  
• Lift the handset from the cradle  
and press TALK so the IN USE  
indicator lights.  
• When you hear a dial tone, press  
MEMORY and then press the  
memory location number where  
the phone number is stored. The  
phone dials the stored number.  
15  
 
43-1031.fm Page 16 Tuesday, August 17, 1999 9:24 AM  
TROUBLESHOOTING  
We do not expect you to have any problems with your telephone, but if you do, these  
suggestions might help. If you still have problems, check other phones on the same  
line to see if they work properly. If they do and the problem does not seem to be with  
your phone service, take your phone to your local Radio Shack store for assistance.  
Problem  
Solution  
The handset does not  
work.  
• Press TALK on the handset.  
• Move the handset closer to the base.  
• Be sure the phone line cord and AC adapter  
are correctly and securely connected.  
• Be sure the battery is charged.  
• Fully extend the base’s antenna vertically.  
• Return the handset to the cradle for 5 sec-  
onds, and then try again.  
• Check the handset and base’s charging con-  
tacts. If they are dirty, clean them with a pencil  
eraser.  
Volume drops or you hear  
unusual sounds on the  
line.  
Someone has picked up another phone on the  
same line. Hang up the other phone.  
Call is noisy.  
• Press CHANNEL to switch to another channel.  
• Do not mount the base near appliances or  
large metal objects.  
• Hang up and redial the number.  
• Keep the handset away from interference  
sources such as computers; remote control  
toys; wireless microphones, alarm systems,  
intercoms and room monitors; fluorescent  
lights; and electrical appliances. If the interfer-  
ence is severe, turn off the interfering device.  
• Fully extend the base’s antenna vertically.  
16  
 
43-1031.fm Page 17 Tuesday, August 17, 1999 9:24 AM  
Problem  
Solution  
The handset’s range  
decreases.  
• Fully extend the base’s antenna vertically.  
• Be sure the antenna is not touching a metal  
surface.  
• Return the handset to the cradle, and recharge  
the battery.  
Receiver sound flutters or  
fades.  
• Be sure the battery is charged.  
• Fully extend the base’s antenna vertically.  
• Be sure the battery is charged.  
• Move the handset closer to the base.  
RINGER  
ON  
to ring.  
Can make calls, but tele-  
phone does not ring.  
• Handset’s  
must be set to  
Telephone company might be using unusual  
ringing methods. Your telephone is designed  
for standard straight line bridged ringing.  
TONE/PULSE  
Can receive calls, but can- Set the  
switch correctly for the type of  
not make calls.  
service.  
You cannot answer/make a The phone might be receiving interference from an-  
call and the handset  
sounds an error tone when  
you lift it from the base or  
other RF signal; or, if the handset is away from the  
base during a long period of AC power failure, the  
phone might lose its access protection code. Re-  
turn the handset to the base for a few seconds.  
TALK  
press  
.
17  
 
43-1031.fm Page 18 Tuesday, August 17, 1999 9:24 AM  
CARE AND MAINTENANCE  
Your Radio Shack ET-531 10-Channel Cordless Telephone with 10-Memory Speed  
Dialing is an example of superior design and craftsmanship. The following sugges-  
tions will help you care for your phones so you can enjoy it for years.  
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids can  
contain minerals that corrode the electronic circuits.  
Handle the phone gently and carefully. Dropping it can damage cir-  
cuit boards and cases and cause the phone to work improperly.  
Use and store the phone only in normal temperature environments.  
Temperature extremes can shorten the life of electronic devices and  
distort or melt plastic parts.  
Keep the phone away from dust and dirt which can cause premature  
wear of parts.  
Wipe the phone with a damp cloth occasionally to keep it looking  
CLEANER  
new. Do not use harsh chemicals, cleaning solvents, or strong deter-  
gents to clean your phone.  
Modifying or tampering with the phone’s internal components can cause a malfunc-  
tion and might invalidate its warranty and void your FCC authorization to operate it.  
If your phone is not performing as it should, take it to your local Radio Shack store  
for assistance. If the trouble is affecting the phone lines, the phone company might  
ask you to disconnect your phone until you have resolved the problem.  
18  
 
43-1031.fm Page 19 Tuesday, August 17, 1999 9:24 AM  
Caution: Your telephone contains a  
rechargeable nickel cadmium battery.  
At the end of the battery’s useful life, it  
must be recycled or disposed of prop-  
erly. Contact your local, county, or  
state hazardous waste management  
authorities for information on recycling  
or disposal programs in your area.  
Some options that might be available  
are: municipal curb-side collection,  
drop off boxes at retailers, recycling  
collection centers, and mail back pro-  
grams.  
REPLACING THE  
BATTERY  
If you follow the instructions in “Charg-  
ing the Battery,” the supplied battery  
should last about one year. When the  
battery loses its ability to fully charge,  
order a 3.6 volt, 300 milliamp battery  
with a connector that fits the connector  
in the battery compartment. You can  
order a replacement battery through  
your local Radio Shack store.  
Install the new battery as described  
below, then charge the battery (see  
“Charging the Battery”).  
THE FCC WANTS YOU  
TO KNOW  
1. Slide off the battery compartment  
cover on the back of the handset  
as shown.  
In the unlikely event that your phone  
causes problems on the phone line,  
the phone company can temporarily  
discontinue your service. If this hap-  
pens, the phone company attempts to  
notify you in advance. If advance no-  
tice is not practical, the phone compa-  
ny notifies you as soon as possible and  
advises you of your right to file a com-  
plaint with the FCC.  
2. Gently pull on the battery wires to  
disconnect the plug, then remove  
the battery.  
Also, the phone company can make  
changes to its lines, equipment, opera-  
tions, or procedures that could affect  
the operation of the phone. The phone  
company notifies you of these changes  
in advance, so you can take the neces-  
sary steps to prevent interruption of  
your phone service.  
3. Insert a fresh battery and connect  
its plug to the pins inside the bat-  
tery compartment.  
4. Replace the cover.  
19  
 
43-1031.fm Page 20 Tuesday, August 17, 1999 9:24 AM  
Your phone might cause TV or radio  
interference even when it is operating  
properly. To determine whether your  
phone is causing the interference, turn  
off your phone. If the interference goes  
away, your phone is causing the inter-  
ference. Try to eliminate the interfer-  
ence by:  
LIGHTNING  
Your phone has built-in protection cir-  
cuits to reduce the risk of damage from  
surges in phone line current. These  
protection circuits meet or exceed FCC  
requirements. However, lightning strik-  
ing the phone lines can damage your  
phone.  
• Moving your phone away from the  
receiver  
Lighting damage is not common. Nev-  
ertheless, if you live an area that has  
severe electrical storms, we suggest  
that you unplug your phone during  
storms to reduce the possibility of  
damage.  
• Connecting your phone to an AC  
outlet that is on a different electri-  
cal circuit from the receiver  
• Contacting your local Radio  
Shack store for help  
If you cannot eliminate the interfer-  
ence, the FCC requires that you stop  
using your phone.  
RADIO SHACK LIMITED WARRANTY  
This telephone product is warranted against manufacturing defects in material and workmanship for one (1) year  
from the date of purchase from Radio Shack company owned stores and authorized Radio Shack franchisees and  
dealers. Within this period bring your Radio Shack sales slip as proof-of-purchase date to any Radio Shack  
store.  
This warranty does not cover damage or failure caused by or attributable to Acts of God, abuse, misuse, improper  
or abnormal usage, faulty installation, improper maintenance, lightning or other incidence of excess voltage, or  
any repairs other than those provided by a Radio Shack Authorized Service Facility, or transportation costs. Radio  
Shack is not responsible or liable for indirect, special, or consequential damages arising out of or in con-  
nection with the use or performance of the product or other damages with respect to loss of property,  
loss of revenue or profit, or costs of removal, installation or reinstallation.  
EXCEPT AS PROVIDED HEREIN, RADIO SHACK MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED  
WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES  
CONTAINED HEREIN. Some states do not allow the limitation or exclusion of incidental or consequential dam-  
ages and some states do not allow limitation or exclusion of implied warranties; therefore, the aforesaid limita-  
tion(s) or exclusion(s) may not apply to the purchaser. There will be charges rendered for repairs to the product  
made after the expiration of the aforesaid one (1) year warranty period.  
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
We Service What We Sell  
9/94  
RADIO SHACK  
A Division of Tandy Corporation  
Fort Worth, Texas 76102  
8A5  
Printed in Hong Kong  
 

QUAD Speaker System Classic Series ESL User Guide
Quantum Computer Drive Atlas III User Guide
RCA CRT Television F26433 User Guide
RedMax Blower HB250 User Guide
Reebok Fitness Treadmill RBTL18921 User Guide
Ryobi Drill HP1202M User Guide
Samsung DVD Player DVD 1080P9 XAA User Guide
Samsung MP3 Player YH 925 User Guide
Samsung Video Game Controller 26 444 User Guide
Schneider Electric Weather Radio ION8800 User Guide