Remington Electric Shaver R 200 User Guide

Microflex R_200_400_IB 8/24/06 2:34 PM Page 1  
®
®
MC  
400  
Use and  
Care Guide  
R-200  
R-225  
R-400 (shown)  
 
Microflex R_200_400_IB 8/24/06 2:34 PM Page 4  
Product Features  
Congratulations on your purchase of a premium  
Shaver Parts  
®
Remington shaver, with revolutionary shaving technology  
(A)  
Which model is yours?  
Corded Cordless  
Operation Operation  
Run  
Time  
Charge  
Time  
Locking  
Trimmer  
Pouch  
X
X
X
R-200  
R-225  
R-400  
Easy-View® Trimmer  
X
X
30 min.  
16 hrs.  
X
(B)  
(D)  
Power Sytem  
Indicator Lights  
(R-400 only)  
Corded (R-200 & R-225)  
shavers can only be used  
with the power cord.  
Charging  
The charging indicator is a  
green light that glows when  
the shaver is being charged.  
(C)  
(H)  
Cordless (R-400) shavers can  
only be used without the  
power cord.  
(A) Head & cutter assembly  
(B) ON/OFF button  
(C) Power port  
(D) Trimmer button  
(E) Head guard  
(F) Cleaning brush  
(G) Storage pouch (Model R-225 & R-400)  
(H) Power cord  
(E)  
(G)  
(F)  
4
5
 
Microflex R_200_400_IB 8/24/06 2:34 PM Page 6  
How to Use  
Usage Tips  
Before using read the important safety  
instruction section in front of the manual.  
Your shaver cannot be overcharged,  
so you can leave it plugged in and  
charging between shaves.  
shave and minimum wear. Avoid  
Getting a close, comfortable  
shave  
holding the shaver at an angle so  
only one head touches the skin. This  
could cause skin irritation.  
Remington shavers need no adjust-  
ments to their heads or cutters before  
you shave. The heads will automatically  
adjust to the contours of your face.  
Removing the Headguard  
Before operating your shaver, remove  
the headguard, which protects the  
head and cutter assembly. It is  
important to remove the headguard  
correctly to avoid damaging the clips  
that hold it to the shaver.  
1. Press lightly on the top of the head  
guard.  
2. Lift the lower rear edge.  
3. Pull the headguard away from the  
shaver.  
! Always keep the protective head  
guard on the shaver head and keep  
the trimmer in the OFF position when  
the shaver is not in use.  
To preserve the life of the batteries,  
allow them to fully discharge every  
six months, then recharge them for  
24 hours.  
Rechargeable shavers like the R-400  
are designed for cordless operation  
only. Plugging it in will not provide the  
power to shave.  
Use short, circular  
strokes. Use your free  
hand to stretch your  
skin. This encourages  
Adjusting to your new shaver  
your whiskers to stand  
As with every shaver, your shave will  
improve over time. So allow about three  
weeks to develop an effective shaving  
style and for your beard to adjust to the  
new shaver. The adaptation period may  
take a little longer if your skin is sensi-  
tive, or if you alternate between shaving  
methods.  
out, making it easier for them  
to enter the cutting chamber.  
It is not necessary to apply pressure  
while shaving, just let the shaver  
glide lightly on your skin. Never  
press hard. Pressing only flattens  
your whiskers, which makes it  
harder for them to enter the cutting  
chamber. It will also wear out the  
cutting surface more quickly. A gentle  
touch makes shaving easier and  
helps avoid possible skin irritation.  
Cordless Operation of the R-400  
Remove the AC power cord from the  
electrical outlet, then remove from  
shaver’s power port.  
To activate the shaver, slide the  
power button up to the ON position.  
Before you begin:  
Wait at least 15  
minutes after getting  
12  
®
Operating the Easy-View  
Corded Operation of the  
R-200 and R-225  
9
3
up before shaving to  
ensure the face is free  
of puffiness that may  
be present from sleeping.  
Make sure your face  
is clean and dry before  
starting.  
Trimmer  
6
The Easy-View®pop-up trimmer extends  
to trim mustache, sideburns, etc.  
Slide the power button down to the  
OFF position.  
To Trim  
Trim mustache  
Connect the supplied AC power cord  
to the shaver’s power port and then  
to an electrical outlet.  
To activate the shaver, slide the  
power button up to the ON position.  
Trimmer is turned off until it is  
extended for use.  
Use the shaver heads to trim the  
lower edge of your mustache. Hold  
shaver at desired trim line for a  
quick, easy, professional trim.  
Use the pop-up trim-  
mer for the upper edge  
of your mustache.  
Extend the trimmer  
and touch the edge  
of it to the desired line.  
Push the trimmer  
button up to pop up  
the trimmer.  
Always use a clean, dry  
shaver.  
Make sure the cutter head  
assembly is in the locked position.  
Charging the R-400  
Hold the shaver  
with the trimmer  
toward you when  
trimming.  
Before using your shaver for the first  
time, charge it for 24 hours.  
To Shave  
NOTE: It may take up to 3 cycles of  
full charge and discharge to maximize  
battery capacity.  
Slide the ON/OFF button  
to activate the shaver  
for shaving.  
After trimming, pull the trimmer  
button downward into the OFF  
position. Leave it in the down  
position when not in use.  
Trim sideburns  
Hold the shaver so all  
the heads touch your  
face together. This  
allows the shaver to  
work the way it was  
designed for the closest  
To charge your shaver  
Slide the power button downward to  
the OFF position.  
Extend the trimmer and  
touch the edge of it to the  
desired trim line.  
NOTE (R-400): It is important to always  
use the button to close the trimmer to  
avoid damaging the locking mechanism.  
Connect the supplied AC power cord  
to the shaver’s power port and then  
to an electrical outlet.  
6
7
 
Microflex R_200_400_IB 8/24/06 2:34 PM Page 8  
Cleaning and Maintenance  
To assure smooth, efficient  
performance, it is important  
to clean your shaver.  
Lubricate  
Cleaning Cautions  
When is it Time to Replace  
Your Heads and Cutters?  
Remington® Shaver Saver® Lubricant  
(SP-4) lubricates and cleans your  
shaver's cutters and head assembly.  
The lubricant helps remove hair clip-  
pings while reducing wear. A quick  
spray after each shave keeps your  
shaver operating at peak performance.  
The construction of this shaver  
is for dry operation only. It is  
not waterproof. Never put the  
shaver partially or completely  
into water.  
It is very important to replace your  
heads and cutters when necessary  
to ensure a close, comfortable  
shave without irritation. We recom-  
mend they be replaced every 12  
months. Here are some signs of  
head and cutter wear, indicating  
that replacement is needed.  
Daily  
Brush inside the  
head assembly  
after each use:  
1. Turn the shaver  
off.  
Never clean the shaver or  
replace the cutters while it is  
plugged into an electrical outlet.  
Do not use an aggressive cleansing  
agent as this may destroy the  
shaver coatings.  
Do not clean or remove the head  
assembly while the shaver is running  
or plugged in, as it may cause dam-  
age to the unit's heads or cutters.  
Replace worn or damaged parts  
with Remington® replacement  
parts only.  
! Important: Make sure to align  
the two locating holes in the Cutter  
Retainer assembly with the pins in  
the Head Frame Assembly. (See  
illustration below). Then tighten  
center screw knob to lock the  
cutters into place.  
2. Grip the head  
assembly by  
the three ridges  
and pull it off the  
shaver.  
3. Use the clean-  
ing brush to  
sweep out the  
internal part of  
the head assem-  
bly and the hair  
pocket area,  
where 3 shaver  
spindles are  
Irritation  
As the heads get excessively worn  
you may experience some skin  
irritation. This would be especially  
noticeable when you apply  
after-shave lotion.  
Replace head assembly on the shaver  
simply by pushing it onto the shaver.  
Cover shaver head with plastic head-  
guard between uses. When removing  
the headguard or placing it back onto  
the shaver,do not apply pressure to  
floating cutter surfaces, as you may  
damage them.  
Pulling  
When the cutters wear you may  
feel a sense of pulling and a loss  
of closeness when you shave. This  
is an indication that it is time to  
replace your heads and cutters.  
located.  
4. Replace head assembly.  
The replacement parts for your  
shaver is model SP-25.  
Cutter retainer  
assembly  
Weekly  
U.S. residents: To order, contact  
us at 800-231-8793, visit us at  
or visit your local retailer.  
Clean under the cutter assembly at  
least once a week:  
Center  
screw  
knob  
1. Turn the shaver off.  
2. Open the head assembly as above.  
3. Unscrew the center screw knob  
to remove the cutter retainer  
assembly.  
4. Use the cleaning brush to sweep  
the dust and hairs from under the  
cutters.  
Locating holes  
Canadian residents: For any shaver  
accessory requirements, please  
call800-268-0425 or visit us at  
Head/frame  
assembly  
5. Replace head assembly.  
Floating  
cutter  
heads  
Locating pins  
8
9
 
Microflex R_200_400_IB 8/24/06 2:34 PM Page 10  
Performance Guarantee  
Battery Disposal  
SPECTRUM BRANDS, INC. SHALL  
CAUTION: DO NOT PUT IN FIRE OR  
MUTILATE YOUR BATTERIES WHEN  
DISPOSING AS THEY MAY BURST OR  
RELEASE TOXIC MATERIALS. DO NOT  
SHORT CIRCUIT AS IT MAY CAUSE  
BURNS. DISPOSE PROPERLY IN  
ACCORDANCE WITH YOUR LOCAL  
AND STATE REQUIREMENTS.  
Full Two-Year Warranty  
Battery Removal (R-400 only)  
When your rechargeable shaver  
reaches the end of its useful life, the  
batteries must be removed from the  
shaver and be recycled or disposed of  
properly in accordance with your local  
and state requirements.  
NOT BE RESPONSIBLE FOR ANY  
INCIDENTAL, SPECIAL OR CONSE-  
QUENTIAL DAMAGES RESULTING  
FROM THE USE OF THIS PRODUCT.  
ALL IMPLIED WARRANTIES, INCLUD-  
ING BUT NOT LIMITED TO IMPLIED  
WARRANTIES OF FITNESS AND  
MERCHANTABILITY, ARE LIMITED  
IN DURATION TO TWO YEARS FROM  
DATE OF ORIGINAL PURCHASE.  
Spectrum Brands, Inc. warrants this  
product against any defects that are  
due to faulty material or workmanship  
for a two-year period from the original  
date of consumer purchase. This war-  
ranty does not include damage to the  
product resulting from accident or  
misuse.If the product should become  
defective within the warranty period,  
we will repair it or elect to replace it  
free of charge. Return your product  
and sales receipt with your name,  
address and day time phone number  
to: Spectrum Brands, Inc. , Attention:  
Consumer Services, 601 Rayovac  
Drive, Madison, WI 53711. For more  
information call 800-736-4648.  
The following procedures should  
be followed for battery removal:  
Make sure your shaver is  
unplugged from any  
outlets, so you dont  
risk an electrical  
The EPA-certified  
®
RBRC Battery  
This warranty gives you specific legal  
rights and you may also have other  
rights which vary from state to state  
or province to province. Some states  
do not allow the exclusion or limitation  
of incidental, special or consequential  
damages.  
Recycling Seal on  
the nickel-cadmium  
(Ni-Cd) battery indicates  
Spectrum Brands, Inc.  
shock.  
Remove the Head  
Assembly by gently  
lifting the assembly  
away from the shaver.  
Using a small Phillips  
head screwdriver,  
is voluntarily participating in an  
industry program to collect and  
recycle these batteries at the end  
of their useful life, when taken out  
of service in the United States or  
Warranty excludes:  
Screens and cutters  
Performance Guarantee  
Spectrum Brands, Inc. Money-back  
Offer  
®
remove the screws  
from the upper and  
lower back of  
Canada. The RBRC program  
provides a convenient alternative to  
placing used Ni-Cd batteries into the  
trash or the municipal waste stream,  
which may be illegal in your area.  
KEEP ORIGINAL SALES RECEIPT AS  
PROOF OF PURCHASE FOR WARRANTY  
PURPOSES.  
If within 30 days after you have  
purchased your Remington® branded  
product, you are not satisfied and  
would like a refund, return it with the  
sales slip indicating purchase price  
and date of purchase to the retailer  
from whom it was purchased.  
Spectrum Brands, Inc. will reimburse  
all retailers who accept the product  
within 30 days from the date of  
purchase. If you have any questions  
concerning the money-back  
the shaver.  
Pull or gently pry the  
shaver halves apart,  
exposing the battery.  
Hold each battery in  
place and very carefully cut the  
wires leading to the terminals on  
each battery.  
SM  
Please call 800-8-BATTERY for  
This warranty does not cover products  
damaged by the following:  
Accident, misuse, abuse or  
alteration of the product  
Servicing by unauthorized persons  
Use with unauthorized accessories  
information on Ni-Cd battery recy-  
cling and disposal bans/restriction  
in your area. Spectrum Brands, Inc.  
involvement in this program is part  
of our commitment to preserving  
our environment and conserving  
our natural resources.  
Lift or pry the battery out of the  
shaver.  
Connecting it to incorrect current  
and voltage  
guarantee, please call 800-736-4648.  
Wrapping cord around appliance  
causing premature wear &  
breakage  
Any other conditions beyond our  
control  
10  
11  
 
Microflex R_200_400_IB 8/24/06 2:34 PM Page 12  
Warranty Service  
R-200, R-225  
120 VAC, 60 Hz  
Dist. by: Spectrum Brands, Inc.,  
Madison, WI 53711  
Dist. by: Rayovac Canada Inc.,  
Mississauga, ON L4W 2T7  
R-400  
105-130 VAC, 60 Hz  
105-240 VAC, 50 Hz  
MADE IN CHINA  
Questions or comments:  
Call 800-736-4648 in U.S. or  
800-268-0425 in Canada.  
products.com  
REMINGTON & MICROFLEX and  
EASY-VIEW are trademarks of  
ROVCAL, INC.  
© 2006 ROVCAL, INC.  
1/06 Job #CS29563  
T22-20903  
12  
 

Radio Shack Cordless Telephone 43 3823 User Guide
Radio Shack Door 63 984 User Guide
RCA CRT Television F20TF20, MR51TF20, F27TF700, MR68TF700 User Guide
RCA Flat Panel Television HD61LPW174 User Guide
RCA Modem RCA DHG535 User Guide
Rival Fryer S16G User Guide
Rosewill Computer Keyboard RK 7310 User Guide
Rosewill Server RSV R26 User Guide
Salton Coffeemaker FCM12SS User Guide
Sanyo Cell Phone S750i User Guide