Ca l. 7 K5 2
INSTRUCTIONS
(P.
3)
BEDIENUNGSANLEITUNG
INSTRUCTIONS
ISTRUZIONI
(S. 33)
(P. 63)
(P. 93)
(P. 125)
(P. 155)
(185 頁)
INSTRUCCIONES
INSTRUÇÕES
用法説明
CAUTION
The SEIKO SCUBA DIVER’S Cal. 7K52 is intended for use in an
inherently hazardous form of recreation. Therefore, it is
absolutely essential that you observe strictly all instructions
for the use and maintenance of the watch set forth in this
booklet.
First of all, this watch is for use by adults only in recreational
(no-decompression) diving in water having a specific gravity
of 1.025 (sea water), having a temperature range of 0° C to 40°
C, and is not for decompression diving, saturation diving or
diving at altitudes (diving in a high mountain lake, etc.). Unless
you have undergone scuba training with a qualified instructor,
you can neither fully appreciate the concept of no-
decompression limits nor properly employ the watch.
3
DO NOT ATTEMPT TO DIVE USING THE WATCH UNLESS YOU
HAVE BEEN PROPERLY TRAINED IN SCUBA DIVING, POSSESS
THE REQUISITE EXPERIENCE AND SKILL TO DIVE SAFELY,
HAVE THOROUGHLY FAMILIARIZED YOURSELF WITH THE
OPERATION AND MAINTENANCE OF THE WATCH, AND HAVE
TESTED ALL WATCH FUNCTIONS PRIOR TO EACH DIVE.
In addition, sharp fluctuations in atmospheric pressure and
aquatic environments may affect the performance of the watch.
When making a dive, use other diving instruments such as dive
computers together with this watch for safety’s sake.
Finally, all of the diving measurements made by the watch and
warning functions of the watch, outlined herein, are to serve as
general guidelines only, and individual reactions will differ
from person to person.
4
CONTENTS
Page
HOW TO USE THE SCREW LOCK TYPE CROWN .....................................................
TIME/CALENDAR SETTING ........................................................................................
ADJUSTING THE HAND POSITION BEFORE DIVING................................................
DIVING MEASUREMENT ...........................................................................................
WARNING FUNCTION FOR DIVING ...........................................................................
RECALL OF LOG DATA ..............................................................................................
ROTATING BEZEL ......................................................................................................
SINGLE-TIME ALARM ................................................................................................
PRECAUTIONS FOR DIVING ......................................................................................
NOTES ON USING THE WATCH ................................................................................
BATTERY LIFE INDICATOR ........................................................................................
BATTERY CHANGE .....................................................................................................
HOW TO USE THE DIVER EXTENDER .......................................................................
SPECIFICATIONS........................................................................................................
8
9
10
11
14
17
18
19
20
23
27
27
30
31
✩ For the care of your watch, see “TO PRESERVE THE QUALITY OF YOUR
WATCH” in the attached Worldwide Guarantee and Instruction Booklet.
5
CAL. 7K52
DIVING MEASUREMENT
● Full automatic measurement of diving data
Current depth, maximum depth, diving time and time submerged
● Recording of log data
Maximum depth, average depth, diving time and time submerged for the last two dives
● Warning functions
• Rapid ascent warning
• Extra measurement range warning
• Abnormal measurement warning
● Rotating bezel
Can measure elapsed time such as diving time, surface interval, etc.
● Battery life indicator
SINGLE-TIME ALARM
● Can be set to ring only once at a designated time within the coming 12 hours.
TIME/CALENDAR
● Hour, minute and small second hands and date
6
Rotating bezel
1/10 m hand
Minute hand
Hour hand
B
A
★
C
a b
c
d
Water contact sensor
Small second hand
CROWN
[Screw lock type]
DIVING TIME hand
DEPTH hand
Date
MAX. DEPTH hand
Time submerged
Alarm time
Pressure sensor is
located under here.
★
a: Screwed-in position
b: Normal position
c: First click
d: Second click
7
HOW TO USE THE SCREW LOCK TYPE CROWN
● To unscrew the crown:
● To screw in the crown:
With the crown at normal position,
turn it clockwise while pressing it.
Turn it counterclockwise.
WARNING
● While you are underwater, never unscrew the crown or pull it out.
● Do not pull out the crown to the first click while the watch is measuring the depth
and for 10 minutes after diving. Otherwise, the depth measurement is stopped,
and false data will be recorded in memory as log data.
8
TIME/CALENDAR SETTING
Hour hand
Minute hand
CROWN
Unscrew.
▼
Pull out to first click and turn counter-
clockwise to set the date.
▼
Pull out to second click when small
second hand is at the “0” position.
▼
Set hour and minute hands.
▼
Date
Press to set small hour and minute
hands to the time set above.
A
A
▼
CROWN
Small
second hand
Small hour and
minute hands
Push in in accordance with a time
signal.
▼
Screw in completely.
9
ADJUSTING THE HAND POSITION BEFORE DIVING
Press repeatedly until you hear a long beep.
B
● With each press of button B, the indication of the diving hands changes as follows:
Diving hands at
“0” position
Log data of
the last dive
Log data of the
dive before last
(Beep, beep)
(A long beep)
(Beep)
● If any of the hands does not return to “0” position, follow the procedure below.
DEPTH hand
1/10 m hand
CROWN
DIVING
TIME
hand
MAX. DEPTH hand
Unscrew, and pull out to second click when
small second hand is at the “0” position.
▼
Press to reset the DIVING TIME hand to
B
B
“0” position.
C
▼
Press to reset the 1/10 m, DEPTH and
MAX. DEPTH hands to “0” position.
▼
C
CROWN
Set the current time. (See “TIME/CALEN-
DAR SETTING)
▼
Push in in accordance with a time signal,
and screw in completely.
10
DIVING MEASUREMENT
● The watch measures the current depth, maximum depth, diving time and time submerged,
and indicates them with the four hands for diving measurement and the small hands at the 6
o’clockposition.
HOW TO READ THE MEAS UREMENTS
● Current depth: Indicated by DEPTH and 1/10 m hands
in 0.1 m increments from 1.6 m up to
55.0 m. (Ex. 12.5 m)
● Maximum depth: Indicated by MAX. DEPTH hand
in 0.5 m increments from 1.5 m up
to 55.0 m. (Ex. 20.5 m)
● Diving time: Indicated by DIVING TIME hand up to
12 hours.
(Ex. 17 minutes)
● Time submerged: Indicated by small hands at the 6
o’clock position. (Ex. 10:10)
11
HOW TO US E THE DIVING FUNCTION
Before diving, check the hands
for diving measurements.
Press button B repeatedly.
Log data
Log data of Diving hands
of the
the dive
at “0”
last dive
before last
position
0.0 m
1.6 m
Diving measurement starts when
you descend to 1.6 m or more.
Never operate the crown while
the measurement is in progress.
55.0 m
12
Case I
Case II
Diving measurement stops when
you ascend to less than 1.6 m.
Rapid ascent warning !
Case I
:
If you stay at less than 1.6 m underwater
for more than 10 minutes, the dive is
considererd to be completed.
Case II : If you descend again to 1.6 m or more
underwater before 10 minutes have
elapsed, the two dives are considered
inseparable, and the measurement is
resumed.
Extra measurement range warning !
13
● Before starting a dive, be sure to check that the hands for diving measurement are reset to “0” position.
If not, reset them following the procedure in “ADJUSTING THE HAND POSITION BEFORE DIVING”.
● When you ascend to a depth less than 1.6 m underwater and the watch stops measuring the depth,
the DEPTH and 1/10 m hands indicate “0.0 m”.
● If you descend again to a depth of 1.6 m or more underwater before 10 minutes have elapsed, the time
elapsed after the depth measurement is stopped is added to the measured diving time.
● For 10 minutes after a dive, all the three buttons will not work.
● After 10 minutes have elapsed following a dive, recall of log data is made possible by pressing button
B.
WARNING FUNCTION FOR DIVING
RAP ID AS CENT WARNING
● The watch monitors the change of depth at 10 second intervals and gives a warning if
the diver ascends more than 3 m in 10 seconds, that is, at a rate of more than 18 m per
minute.
Beep
Beep
Warning sound beeps intermittently for
about 10 seconds and 1/10 m hand
moves back and forth.
14
CAUTION
The rapid ascent warning is given whenever the diver’s ascent rate is beyond the
specified criterion. The extent of hazardousness, however, varies depending on the
water temperature and the diver’s physical condition. Please note that the warning
serves only as a guideline for your diving activities.
EXTRA MEAS UREMENT RANGE WARNING (LIMIT)
● If the measured depth exceeds 55.0 m, the
DEPTH and MAX. DEPTH hands point to
the 56-minute position, “LIMIT”.
“LIMIT”
position
* If the diver returns to a depth of 55.0 m or less,
the DEPTH hand indicates the depth properly.
ABNORMAL MEAS UREMENT / MEAS UREMENT HALT WARNING
● If the watch senses an abnormality in depth measurement, the diving measurement is
automatically halted.
15
The DEPTH hand points to the 58-minute
position and the MAX. DEPTH hand
points to 0 m.
CAUTION
If the watch gives the above warning, do not continue to use the watch for diving
measurement.
16
RECALL OF LOG DATA
● The watch retains data for two dives, namely, time submerged, diving time, maximum depth
and average depth.
*Log data cannot be recalled while diving and for 10 minutes after diving.
Press to recall the log data.
B
● With each press of button B, recall of the log data and checking of the hand positions are
made in the following order.
Log data of
Log data of the
dive before last
Diving hands at
“0” position
the last dive
(Beep, beep)
(A long beep)
▼
(Beep)
Average depth
B
Diving time
Maximum depth
* If the single-time alarm has
been engaged, it is canceled
by pressing button B.
Time submerged
17
ROTATING BEZEL
● The rotating bezel can show up to 60 minutes of elapsed time.
It is useful for measuring the surface interval.
1
Turn the rotating bezel to align
2
Read the number on the rotating
bezel that the minute hand points
to.
its “
” mark with the minute
hand.
Start
20 minutes
have elapsed.
Elapsed time
* The rotating bezel turns only counterclockwise for safety’s sake.
18
SINGLE-TIME ALARM
● The alarm can be set to ring once within the coming 12 hours.
● While on the surface, the small hands at the 6 o’clock position serve as alarm hands.
*While you are at a depth of 1.6 m or more underwater and for 10 minutes after a dive, the single-time
alarm function cannot be used.
ALARM TIME S ETTING
Press to reset the hands for diving
measurement to “0” position.
B
▼
B
Set the alarm time.
A
* At the designated time, the alarm rings for 20
seconds and is automatically disengaged.
● To stop the alarm manually:
Press any of the buttons.
A
● To cancel the alarm:
Press button B to recall the log data, or press
Small hour and minute hands
and hold button A until the small hands indicate
the current time.
Ex.: Alarm time is set at “10:30”.
19
PRECAUTIONS FOR DIVING
BEFORE DIVING
● Check that:
• the watch operates normally.
• the crown is locked tightly in place.
• there are no visible cracks in the crystal or the watch band.
• the strap or bracelet is securely fastened to the watch case.
• the buckle keeps the strap or bracelet firmly secured to the wrist.
• the time and date are properly indicated.
• the small second hand is moving at one-second intervals.
• the log data of the previous two dives is recalled properly.
• all the hands for diving measurement are reset to “0” position.
While the small second hand is moving at two-second intervals, or when the DEPTH hand
points to the 58-minute position after all the hands are reset to “0” position, the watch will
not measure the depth. In these cases, replace the battery with a new one. (See “BATTERY
LIFE INDICATOR”)
If there are any malfunctions, do not use the watch for diving. We recommend that you
contact an AUTHORIZED SEIKO SERVICE CENTER.
● If the temperature of the water is much lower than the air temperature (for example, if the
watch is put into water after it is left in direct sunlight for a long time), the watch may not
measure the depth accurately. In this case, soak the watch in water for approximately 5
minutes before starting to dive.
● If the watch is used in places where atmospheric pressure or temperature changes sharply,
20
or in temperatures outside the operational temperature range for depth measurement (0°
C to 40° C or 32° F ~ 104° F), the depth measurement may be inaccurate, and depths greater
than 1.6 m may be displayed even while the diver is on the surface, resulting in endless
depth measurement and buttons which no longer operate. If this occurs, unscrew the crown
and pull it out to the first click to manually stop the measurement.
*Measurement details are recorded as abnormal measurement. (See “Abnormal measurement/
measurement halt warning” in “NOTES ON USING THE WATCH”) After the measurement is stopped,
push in the crown and screw it in completely.
● By making a new dive, the older of the two log data in memory will be erased. Before diving,
therefore, it is recommended that you make a note of the stored data in your log book, etc.
WHILE DIVING
● Use the watch only within the operational temperature range for depth measurement (0° C
~ 40° C or 32° F ~ 104° F).
● Take care not to hit the watch against hard objects such as rocks.
● While you are underwater, never unscrew the crown or pull it out.
● Check that the DEPTH hand moves properly.
● While you are at a depth of 1.6 m or more underwater, the alarm will not ring so that it is
not confused with the beeping sound for the rapid ascent warning.
● The depth measurement is made every second except while the DEPTH hand is moving.
● While the watch is giving the rapid ascent warning, it will not measure the depth. In some
cases, however, the watch stops the warning momentarily to indicate the depth and then
resumes the warning.
● Depending on the aquatic environment where the watch is used, the beeping sound for the
21
rapid ascent warning may or may not reach your ears.
● If you find the DEPTH hand indicating the 58-minute position while you are underwater, you
should either ascend to the surface immediately or, if you choose to remain underwater, not
depend on diving information provided by the watch.
● The watch measures the depth of water on the basis of seawater having a specific gravity
of 1.025. When it is used in fresh water such as lakes, therefore, the displayed depth should
be corrected by multiplying it by 1.025.
Ex. Assuming that the gravity of the lake where you are diving is 1.00
If the watch indicates 29.2 m, the actual depth is:
29.2 m x 1.025/1.00 = 30.0 m
● While you are underwater, none of the buttons will work for safety’s sake.
AFTER DIVING
● After making a dive, be sure to rinse the watch in fresh water, and wash out all seawater,
soil, sand, etc. If dust forms between the case and rotating bezel, the pressure sensor will
not function properly.
● Be sure to wash out soil, etc. sticking to the water contact sensor unit, as this will cause a
malfunction.
● After cleaning the watch in fresh water, be sure to wipe it thoroughly dry to prevent possible
rust on the case.
● If soil, sand, etc. stick in the sensor unit and cannot be washed out, take your watch to the
retailer from whom the watch was purchased or an AUTHORIZED SEIKO DEALER or
SERVICE CENTER.
● Be careful not to expose the watch to solvents such as alcohol and gasoline, as this may
cause a malfunction of the sensors.
22
NOTES ON USING THE WATCH
TIME/CALENDAR SETTING
●
Do not set the date between 9:00 p.m. and 1:00 a.m. Otherwise, the date may not change properly.
●
Be sure to set the time hands and the small hands at the 6 o’clock position accurately to the current
time as the time submerged recorded as log data is based on the time the small hands indicate.
●
By pulling out the crown to the second click, the time hands stop moving, and the small hour and
minute hands indicate the current time and stop. The hands for diving measurement are reset to the
“0” position.
●
●
When setting the hour hand, check that AM/PM is correctly set. The watch is so designed that the
date changes once in 24 hours.
When setting the minute hand, advance it 4 to 5 minutes ahead of the desired time and then turn it
back to the exact time.
●
●
The small hour and minute hands advance quickly if button A is kept pressed.
It is necessary to adjust the date at the end of February and 30-day months.
ADJUSTING THE HAND POSITION BEFORE DIVING
●
●
●
The hands move quickly if the respective buttons are pressed.
The MAX. DEPTH hand moves only when it is pushed by the DEPTH hand from the clockwise direction.
With each press, the 1/10 m hand advances by 1/4 of a graduation. When the DEPTH hand nears “0”
position, the 1/10 m hand is hidden behind it. Count the number of presses of button C required to
reset the 1/10 m hand to “0” before it is completely hidden.
●
Do not press buttons B and C at the same time.
23
DIVING MEASUREMENT
How to read the measurements
●
The time submerged is the time when you descend to a depth of 1.6 m or more underwater, and the
diving time measurement starts at the same time.
●
●
The time submerged is indicated in the 12-hour indication without showing AM/PM.
The diving time can be measured and indicated for up to 12 hours, but it is only recorded for up to 2 hours
as the log data in memory.
●
●
The DIVING TIME hand moves at 1/5-minute intervals, but the scale is graduated in minutes.
Do not press buttons B and C at the same time.
How to use the diving function
●
Even if you have never made a dive using the watch, log data of two dives is prerecorded in memory
for checking purposes.
●
If you start a dive without resetting the hands to “0” position, they automatically return to “0”
position as the watch starts measuring and then move to indicate the depth and diving time.
However, you cannot check the current depth all this while, so therefore be sure to reset the hands
to “0” position before diving.
WARNING FUNCTION FOR DIVING
Rapid ascent warning
●
If the diver ascends so fast that the DEPTH hand cannot move exactly in accordance with the actual
change of depth, the 1/10 m hand does not move back and forth but alternately moves and stops
as a warning.
Extra measurement range warning
●
If a depth of more than 55.0 m is measured, the log data recorded in memory will be as follows:
24
• Maximum depth : The MAX. DEPTH hand indicates the 56-minute position.
• Average depth The DEPTH hand indicates the 56-minute position.
:
• Time submerged and diving time are recorded as measured.
Abnormal measurement / measurement halt warning
●
If the watch senses an abnormality while measuring the depth, the log data recorded in memory will
be as follows:
• Maximum depth : The MAX. DEPTH hand indicates “0” position.
• Average depth
:
The DEPTH hand indicates the 58-minute position.
• Time submerged and diving time measurements are also abnormal, and the recorded data should
not be considered reliable.
RECALL OF LOG DATA
●
When log data is recalled by pressing button B for the first time when 10 minutes have elapsed after
diving, the data newly recorded is recalled. At this time, only the DEPTH hand moves to indicate the
average depth, as the other hands are already indicating the data just obtained.
●
●
●
The time submerged is indicated in the 12-hour indication without showing AM/PM.
The time submerged is retained in memory even if a time adjustment is made.
The watch measures the diving time for up to 12 hours, but, in recalling the log data, up to 2 hours are
indicated. To show the time beyond 1 hour, the DIVING TIME hand makes another revolution.
●
Remarks on the indication of MAX.DEPTH and DEPTH hands
•
When both the MAX. DEPTH and DEPTH hands point to the 56-minute position:
This indicates that a depth of more than 55.0 m is measured during the dive and that the maximum
and average depths cannot be calculated. The time submerged and diving time are recorded
properly.
When the MAX. DEPTH and DEPTH hands point to “0” and the 58-minute positions, respectively:
This indicates that the watch senses an abnormality in depth measurement during the dive.
Measurement of the time submerged and diving time are also abnormal.
•
25
SINGLE-TIME ALARM
●
When button B is pressed to reset the hands for diving measurement, check that the small hands at
the 6 o’clock position indicate the current time.
●
While you are at a depth of 1.6 m or more underwater and for 10 minutes after a dive, the single-time
alarm function cannnot be used.
●
●
The small hour and minute hands advance quickly if button A is kept pressed.
Do not recall the log data while the alarm is engaged. Otherwise, the small hands at the 6 o’clock
position move to indicate the time submerged and the alarm time you have set is automatically
canceled.
●
The alarm time you have set is also canceled automatically when the watch is used for diving.
26
BATTERY LIFE INDICATOR
● When the battery nears its end, the small second hand moves at two-second intervals
instead of the normal one-second intervals. In that case, the watch will stop operating
in 2 to 3 weeks. Replace the battery with a new one as soon as possible.
* While the small second hand is moving at two-second intervals, the watch remains accurate but the
alarm will not ring.
● While the small second hand is moving at two-second intervals, do not use the watch
for diving, as the watch does not measure the depth.
● When the battery nears its end, the DEPTH hand
indicates the 58-minute position when button B is
pressed to reset the hands for diving measurement
to “0” position.
* When the log data is displayed, however, the DEPTH hand
does not indicate the 58-minute position.
BATTERY CHANGE
The miniature battery which powers your watch should last approximately
2 years. However, because the battery is inserted at the factory to check
2
the function and performance of the watch, its actual life once in your
Years
possession may be less than the specified period. When the battery expires,
be sure to replace it as soon as possible to prevent any malfunction. For
battery replacement, we recommend that you contact an AUTHORIZED
SEIKO DEALER and request SEIKO CR2016 battery.
27
* For safety’s sake, the watch will also undergo a strict check at the time of battery replacement. In
addition to battery replacement, water resistant quality of the watch and the depth measurement
function will be checked. The gasket will be replaced with a new one if necessary. Therefore, it
will take approximately 10 days before the watch is returned to you, and the checking may be made
at cost.
* The battery life may be less than 2 years if the alarm is used more than 15 seconds a day, and/or
the depth measurement function more than 50 times a year, one hour per dive.
* When the battery is replaced with a new one, or when it runs down, the log data will be erased from
memory.
WARNING
● Do not remove the battery from the watch.
● If it is necessary to take out the battery, keep it out of the reach of children. If
a child swallows it, consult a doctor immediately.
CAUTION
● Never short-circuit, heat or otherwise tamper with the battery, and never
expose it to fire. The battery may burst, become very hot or catch fire.
● The battery is not rechargeable. Never attempt to recharge it, as this may cause
battery leakage or damage to the battery.
28
Necessary procedure after battery change
● When the battery is replaced with a new one or when the watch hands move improperly, follow the
procedure below. The IC is reset and then the watch operates normally.
* The log data stored in memory will be erased by following the procedure below.
Pull out Crown to the second click and press buttons
B and C at the same time.
C
B
➠
Before using the watch:
● Set the time and date.
● Press button B to recall the log data.
The following data will be displayed.
Diving time
Maximum depth
Average depth
Time submerged
DATA 1
DATA 2
15 minutes
30 minutes
20 m
40 m
10.0 m
20.0 m
Time randomly selected
Time of DATA 1 plus 6 hours
* If the above data are not properly indicated, the watch may be out of order. Contact the retailer from whom
the watch was purchased or an AUTHORIZED SEIKO DEALER.
29
HOW TO USE THE DIVER EXTENDER
Upper cover
Flap
Clasp
2
12 o’clock
side
1
6 o’clock
side
Two-piece
foldover portion
● To extend the band length
1 Lift up the flap.
2 Press the button to open the clasp.
* Then, push the flap back to the normal position for
safety’s sake.
3 Pull the two-piece foldover portion until it clicks
loose.
4 Slide the upper cover in the direction of the
arrow, and then,
3
➡
5
4
5 pull it up to extend the two-piece foldover
6
portion to the full.
Approx. 2 cm
6 Close the clasp, and then, the flap.
● To change back the band length
Fold the two-piece foldover portion, and hook the
upper cover on to the shaft of the flap. Then, pull
the bracelet hard until the two-piece foldover
portion fixed in position.
30
SPECIFICATIONS
1
2
Frequency of crystal oscillator ................... 32,768 Hz (Hz = Hertz ... Cycles per second)
Loss/gain (monthly rate) ............................. Less than 15 seconds at normal temperature range (5° C
~ 35° C) (41° F ~ 95° F)
3
Operational temperature range .................. –10° C ~ +60° C (14° F ~ 140° F)
0° C ~ +40° C (32° F ~ 104° F) for water depth
measurement function
4
5
Driving system ........................................... Step motor, 4 pieces
Display system
TIME/CALENDAR display ....................... Hour, minute and small second hands and date
DEPTH MEASUREMENT display ............ Current depth by DEPTH hand and 1/10 m hand
Maximum depth by MAX. DEPTH hand (in 0.5 m
increments)
Diving time by DIVING TIME hand (in 1/5 minute
increments)
Time submerged by the small hour and minute hands at
the 6 o’clock position
LOG DATA display .................................. Stores details of two dives.
Maximum depth by MAX. DEPTH hand (in 0.5 m
increments)
Average depth by DEPTH hand and 1/10 m hand
Diving time by DIVING TIME hand (in 1/5 minute
increments)
Time submerged by the small hour and minute hands at
the 6 o’clock position
ALARM display ....................................... Small hour and minute hands at the 6 o’clock position
• While disengaged
• While engaged
:
:
Current time
Designated alarm time
31
Accuracy of the alarm: ±1 minute
6
7
Battery ....................................................... Miniature lithium battery SEIKO CR2016, 1 piece
Battery life: approx. 2 years
Battery life indicator ................................... When the battery life nears its end, the small second hand
moves at 2-second intervals and the DEPTH hand points
to the 58-minute position before diving.
8
9
IC (Integrated Circuit) ................................. C-MOS-LSI, 2 pieces
Semiconductor pressure sensor, 1 piece
Accuracy of sensors
Water depth ............................................ Within ±(Indicated value x 3.0% + 0.5 m) at a stable
temperature
[Influence of temperature change]
Within ±1 m for a temperature change of 20° C
10 Magnetic resistance ................................... 4,800 A/m (60 gauss)
11 Water resistance ........................................ Withstands water pressure to a depth of 200 m and is
therefore suitable for scuba diving.
12 Safety design ............................................. The case, bracelet and buckle are rounded to prevent
damage to the diving suit or user’s skin.
* The specifications are subject to change without prior notice for product improvement.
32
|